Machine Shop: Services & Pricing
|
Cylinder Head Work: |
||
| Prices subject to change without notice | Labor Pricing | |
| Part # | *Starting @ | |
| ZZ-BPH-V6 | Disassemble V6 Cast Iron heads, tank, glassbead, mag, detail, paint, blue print valve job, re-assemble, set up springs | $350.00 |
| ZZ-BPH-L6 | Disassemble L6 Cast Iron head, tank, glassbead, mag, detail, paint, blue print valve job, re-assemble, set up springs | $325.00 |
| ZZ-BPH-CI | Disassemble Cast Iron V8 heads, tank, glassbead, mag, detail, Paint, blue print valve job, re-assemble, set up springs | $450.00 |
| ZZ-BPH-A | Disassemble Aluminum V8 heads, Clean, Mag, Blue Print Valve Job, re-assemble, set up springs | $400.00 |
| ZZ-SBPH | Disassemble Heads * 32 Valves, Tank, Mag, Valve Job & Set up Springs | $550.00 |
| ZZ-DH | Dis-Assemble New V8 Heads, Hone Guides, Re-Seat Valves and Set Up Springs | $150.00 |
| ZZ-INH | Dis-Assy Inspect New V8 Heads, Check Guides & Springs Pres. | $75.00 |
| ZZ-VJ | Blue Print Valve Job Only V8 | $300.00 |
| ZZ-HCC | CC One Chamber | $50.00 |
| ZZ-CCH-1 | CC One Chamber & Intake Runner | $100.00 |
| ZZ-SCH | CC Heads and make all Chambers Same CC's (set) | * $320.00 |
| ZZ-TMPH | Tank V8 Cast Iron Heads, Glassbead, Mag, Detail & Paint Heads | $200.00 |
| ZZ-TMH | Tank V8 Cast Iron Heads, Glassbead & Mag Heads * No Paint | $100.00 |
| ZZ-SH | Surface V6 / V8 Heads (pair) | $120.00 |
| ZZ-SH-6 | Surface 6 Cylinder Head | $90.00 |
| ZZ-BWG | Install Bronze Wall Guides V8 | $180.00 |
| ZZ-BWG-6 | Install Bronze Wall Guides 6 Cylinder | $135.00 |
| ZZ-IIG | Install Cast Iron Guide Each & Fit | 9.50 ea |
| ZZ-ISG | Install Solid Bronze Guide Each & Fit | 11.50 ea |
| ZZ-IVS | Install Valve Seat | $20.00 |
| ZZ-IHC | Install Heli-Coil | $5.50 Ea |
| ZZ-CPC | Machine Heads for Teflon Seals | $40.00 |
| ZZ-RS | Remove Press In Studs & Machine for Screw-In Studs | *$125.00 |
| ZZ-CSGP | Remove Studs in Heads & Machine for Studs & Guideplates (Chev) | $200.00 |
| ZZ-FMSG | Remove Studs In Heads & Machine for Studs & Guideplates (Ford) | $225.00 |
| ZZ-IHS | Machine Aluiminum Heads for Head Savers | $125.00 |
| ZZ-MH | Machine Heads for Larger Springs | $60.00 |
| ZZ-MHBV | Machine Heads for Larger Valves | $100.00 |
| ZZ-MHC | Machine Heads for Spring Cups | $60.00 |
| ZZ-PTH | Pressure Test Heads | $75.00 |
| ZZ-MMVI | Machine Gen V & VI for 7/16 Rocker Studs | $90.00 |
| ZZ-ORCH | Machine Heads for O'Rings | $225.00 |
| ZZ-SPM | Machine Heads for Taper Spark Plugs | $125.00 |
| ZZ-SUH | Set up Springs on Heads (set) | $95.00 |
| ZZ-GMI | Gasket Match Intake Side of Heads | *$125.00 |
| ZZ-GME | Gasket Match Exhaust Side of Heads | *$125.00 |
| ZZ-PEX | Port Exhaust Flanges to Fit Heads | *$145.00 |
| ZZ-MPH | Match Port Heads * Intake & Exhaust Gasket Match | * $250.00 |
| ZZ-HBP | Blend Bowls, Clean up Chambers | * $200.00 |
| ZZ-SP | Street Port Cast Iron or Aluim Heads | *$450.00 |
| ZZ-PPR | River Racer Port Cast Iron or Aluim Heads | * $550.00 |
| ZZ-PP | Port & Polish Cast Iron Heads | * $850.00 |
| ZZ-PP1 | Port & Polish Aluiminum Heads | * $750.00 |
| ZZ-GWH | Grind welded Area's in heads & Clean Up Ports | * $200.00 |
| ZZ-WH | Weld Cast Iron Cylinder Head | * $175.00 |
| ZZ-WAH | Weld Aluiminum Cylinder Head | * $150.00 |
| ZZ-CHMW | Custom Machine Head Work (Hourly) | $100.00 pr Hr |
| Intake Manifold Work | ||
| Desciption of work | Labor Pricing | |
| Part # | Prices subject to change without notice | *Starting @ |
| ZZ-TCIM | Tank, Glassbead & Clean Cast Iron Manifold | $135.00 |
| ZZ-PMI | Gasket Match Intake Mainfold | $85.00 |
| ZZ-PMI-F | Port Match Intake Manifold with Runner Work | *$150.00 |
| ZZ-MIM | Mill Intake Manifold | $225.00 |
| Block Work | ||
| Desciption of Work | Labor Pricing | |
| Part # | Prices subject to change without notice | *Starting @ |
| ZZ-HTOR | Hot Tank Block & Oil Removal | $65.00 |
| ZZ-HTB | Hot Tank, Wash & Bag Block | $85.00 |
| ZZ-WBK | Final Wash & Bag Block | $50.00 |
| ZZ-WPB | Wash, Prep & Paint Block ( New Block) | $150.00 |
| ZZ-MB | Tank, Glassbead & Mag (No Paint) | $100.00 |
| ZZ-DB | Detail Cast Iron Block ( Tank, Glassbead, Mag, Detail & Paint) | $200.00 |
| ZZ-DAB | Detail Aluminum Block ( Tank, Mag & Clean ) | $125.00 |
| ZZ-MEB | Mag Cast Iron Block Only | $40.00 |
| ZZ-HB | Hone Block ( Deglaze) | $155.00 |
| ZZ-TPH | TP Hone Block ( With Torque Plate) | $320.00 |
| ZZ-BH | Bore & Hone Block (No Torque Plate) | $320.00 |
| ZZ-BTPH | Bore & Torque Plate Hone Block (bore up to .060) | $485.00 |
| ZZ-CLB | Check & Measure Align Bore | $75.00 |
| ZZ-LHB | Align Hone Block to Size | $225.00 |
| ZZ-LBB | Bore & Align Hone Block | $360.00 |
| ZZ-ORB | O'Ring Block & Install O'Ring Wire | $325.00 |
| ZZ-IOR | Cut Wire & Install O'Ring Wire in Block | $95.00 |
| ZZ-SD | Square Deck of Block | $200.00 |
| ZZ-ICB | Install Cam Bearings | $75.00 |
| ZZ-ISB | Machine and Install Inside Bolt Kit | $165.00 |
| ZZ-IS | Machine Block & Install Sleeve (Each) | $150.00 |
| ZZ-BLB | Bush Lifter Bores on Block | *$500.00 |
| ZZ-IMC | Machine Block & Convert to 4 Bolt Main | $650.00 |
| ZZ-MOCK | Mock up Engine & Clearance Grind for Stroker | $250.00 |
| Rods & Pistons Work | ||
| Desciption of work | Labor Pricing | |
| Part # | Prices subject to change without notice | *Starting @ |
| ZZ-MR | Clean and Mag Rod (Each) | $6.00 |
| ZZ-DR | Mag, Polish & Shotpeen V8 Rods | $160.00 |
| ZZ-BCR | Back Cut Rods For Stroker | $64.00 |
| ZZ-CR | Cut Rods for Side Clearance | $80.00 |
| ZZ-BR | Bush Rods | $160.00 |
| ZZ-HRB | Hone Rod Bushings to Fit Pins | $64.00 |
| ZZ-HPB | Hone Pin Bosses | $64.00 |
| ZZ-IRB | Install Rod Bolts and Resize Rods | $92.00 |
| ZZ-PFR | Pin Fit Rods | $48.00 |
| ZZ-PFRP | Pin Fit Rods & Pistons | $64.00 |
| ZZ-FCP | Fly Cut V8 Pistons | *$96.00 |
| ZZ-MTP | Machine Top of Pistons (Each) | $20.00 |
| ZZ-PRD | Press Rods & Pistons Off | $48.00 |
| ZZ-PR | Press Rods & Pistons Off & On | $64.00 |
| ZZ-RER | Resize and Equal-Length Rods | $80.00 |
| ZZ-CCB | Cut Rods & Main Bearings for Larger Crank | $96.00 |
| ZZ-CFR | Cut & Fit Rings V8 | $125.00 |
| ZZ-ARP | Assemble Rods & Pistons V8 | $80.00 |
| Crankshaft Work | ||
| Description of work | Labor Pricing | |
| Part # | Prices subject to change without notice | *Starting @ |
| ZZ-MC | Tank, Clean and Mag Crankshaft | $60.00 |
| ZZ-DC | Tank, Clean, Mag, Straighten, Champher & Detail Crankshaft | $145.00 |
| ZZ-PC | Polish Crankshaft | $50.00 |
| ZZ-MSP | Mag, Straighten & Polish Crankshaft | $95.00 |
| ZZ-IC | Index Grind Crankshaft | $225.00 |
| ZZ-MCS | Machine 400 Chevrolet Crankshaft for 383 Stroker | $335.00 |
| ZZ-OSGC | Offset Grind Crankshaft | *$350.00 |
| ZZ-SGCS | Stroker Grind Crankshaft | $450.00 |
| ZZ-CUT | Cut 1/4" Keyway In Crankshaft | $95.00 |
| ZZ-CCC | Cam Cut Crankshaft for Rod Lengths | *$200.00 |
| Camshaft Work | ||
| Description of work | Labor Pricing | |
| Part # | Prices subject to change without notice | *Starting @ |
| ZZ-CG | Change Grind on CSC Cam Core | $70.00 |
| ZZ-SGC | Surface Grind Camshaft | *$75.00 |
| ZZ-SGVW | Surface Grind VW Camshaft | $45.00 |
| ZZ-TUC | Touch Up Grind CSC Camshaft | *$55.00 |
| ZZ-RC | Regrind Flat Tappet Camshaft | *$110.00 |
| ZZ-RRC | Regrind Solid Roller Camshaft | *$150.00 |
| ZZ-RHRC | Regrind Hydraulic Roller Camshaft | *$125.00 |
| ZZ-RCFH | Regrind Flat Head Camshaft | *$145.00 |
| ZZ-PFC | Profile Camshaft | $55.00 |
| ZZ-DSRC | Straighten, Detail & Polish Camshaft | $65.00 |
| ZZ-UC | Undercut Camshaft | *$65.00 |
| ZZ-CGC | Cut Groove in Camshaft | $25.00 |
| ZZ-CJ | Cut Journals on Camshaft | *$75.00 |
| ZZ-DBC | Drill Rear of Camshaft | $35.00 |
| ZZ-SCC | Side Cut Camshaft | $45.00 |
| ZZ-SBC | Grind Camshaft on a Small Base Circle | $50.00 |
| ZZ-SC | Stroker Cut Camshaft | $45.00 |
| ZZ-SCVW | Stroker Cut VW Camshaft | $25.00 |
| Machine Shop Work | ||
| Description of work | Labor Pricing | |
| Part # | Prices subject to change without notice | *Starting @ |
| ZZ-CB | Complete Balance Engine (No Heavy Metal) | $250.00 |
| ZZ-IM | Install Mallory in Crankshaft ( For Balance ) | *$175.00 |
| ZZ-MBF | Match Balance Flexplate / Flywheel | *$65.00 |
| ZZ-MBH | Match Balance Harmonic Balancer | *$55.00 |
| ZZ-CUT-HB | Cut 1/4" Keyway in Harmonic Balancer | $65.00 |
| ZZ-HHB | Hone Harmonic Balancer | $45.00 |
| ZZ-CD | Curve Distributor | $125.00 |
| ZZ-BOBP | Block Off Oil by Pass | $25.00 |
| ZZ-IFP | Install Freeze Plug & All Plugs Kits | $50.00 |
| ZZ-DE | Disassemble Engine | *$125.00 |
| ZZ-GBP | Tank, Glassbead & Paint or Clean Parts (hourly) | *$60.00 |
| ZZ-OP-BP | Blue Print Oil Pump | $75.00 |
| ZZ-RRA | Rebuild Rocker Assembly | *$120.00 |
| ZZ-RBC | Rebuild Used Carburetor | *$150.00 |
| ZZ-SUC | Set up New Carburetor | *$100.00 |
| ZZ-SFW | Surface Flywheel | $75.00 |
| ZZ-VENTED | Vent Fuel Pump Marine | $35.00 |
| ZZ-WP | Weld Oil Pump Pick-Up | $45.00 |
| ZZ-IFPK | Install Fuel Pump Repair Kit | *$25.00 |
| ZZ-IHC | Install Heli-Coils (Each) | $5.50 Ea |
| ZZ-ZBAG1 | Lay Out all Parts, Assemble Rods & Pistons, Wash & Bag for Assembly | $230.00 |
| ZZ-ZBAG | Lay Out all Parts, Clean & Paint all Bolt on Parts, Wash & Bag for Assembly | $275.00 |
| ZZ-ZBAG2 | Lay Out all Parts, Install Plug Kit, Assemble Rods & Pistons, Wash & Bag for Assembly | $280.00 |
| ZZ-ZBAG3 | Lay Out all Parts, Wash & Bag for Assembly | $150.00 |
| ZZ-ZEBP | Complete Blue Print and Assemble Engine | *$2500.00 |
| ZZ-ZFE | Freshen Up CSC Engine Complete | *$1500.00 |